Home > Buffalo Linkstation > Buffalo Nas Error Codes

Buffalo Nas Error Codes

Contents

Do not turn off LinkStation. E22 Mounting of the hard drive failed. I'd say 95-98% of my data is backed up (to a USB 2tb drive) so it's not the end of the world if this dies, but 1) I'd laike to save Is "overuse" likely to have caused it? check over here

After replacement, rebuild the RAID array after starting the LinkStation. LED is OFF The LinkStation is OFF. I21 Checking the hard drive. Off Power is not connected.

Buffalo Linkstation Flashing Red Light

Please tell us how we can make this answer more useful. Yes No Thank you for your cooperation in the questionnaire. Information code Descriptions E04 Firmware is failed. I46 Data is being transferred or RAID is being migrated.

I25 Updating the firmware. *Do not turn LinkStation OFF during the update. I25 Updating the firmware. *Do not turn LinkStation OFF during the update. E14 The RAID array cannot be mounted. Buffalo Linkstation Flashing Red Light 3 Times The number of long flashes give the first of two numbers and the number of short flashes give the second.

Note: When the hard drive is failed, the tab of lower part of the failed hard drive glows red when the front cover is opened. Replace the failed drive indicated by the red LED. Set the hard drive again after shutting down the LinkStation. I22 Erasing the data of the hard drive.

I14 The RAID array is being checked. Buffalo Nas Amber Light I13 The RAID array is being formatted. Don't waste yourtime. If the error still appears after formatting and restarting, replace the hard drive.

Buffalo Linkstation Info/error Solid Orange

Logged Jotin Big Bull Posts: 4201 Re: Linkstation Pro (LS-WXL) Errors (red and orange lights) « Reply #8 on: November 08, 2011, 01:46:47 pm » You need to replace disk 2. E13 An error occurred in the RAID array. Buffalo Linkstation Flashing Red Light I11 The bad sectors in the hard drive may have reached a dangerous level. Buffalo Linkstation Red Light Flashing 7 Times I13 Formatting the RAID array.

E13 An error occurred in the RAID array. check my blog I16 The RAID array is being created. Format the hard drive. Blinking green Accessing. Buffalo Linkstation Solid Orange Light

I23 1s place of information code The LED illuminates for 0.5 seconds every 0.3 seconds. Details Products OS / Hardware Was this answer helpful? Hope this helps Categories Android Phones Audiophile Buffalo Quad Pro NAS Computer Computer, Hardware, Software, How-to's Fujitsu ScanSnap S1500 Going Paperless Hardware How-to's HP Microserver N40L Miscellaneous Photography and Camera Gears http://contactmailsupport.com/buffalo-linkstation/buffalo-ls-wxl-error-codes.php Format the hard drive.

The number of flashes is the tens place of the error code. Buffalo Linkstation Degraded Mode E10 The LinkStation is running on the UPS battery due to a power outage. Operation will continue, but in degraded mode.in RAID1, 5 and 10 modes.

Information code Descriptions E15 The bad sectors in the hard drive have reached a dangerous level Contafct technical support for assistance.

Transfer speeds are slower during the resyncing process. Perform disk checking of the RAID array on the web Admin interface of LinkStation. The LED will blink blue during start up and during the firmware update process. Buffalo Terastation Error Codes Format the hard drive.

E22 1s place of error code The LED illuminates for 0.5 seconds every 0.3 seconds. When starting DirectCopy After the USB device is connected, pressing the LinkStation Function button while the Function LED is solid blue (about 60 seconds) copies the data from the USB device Matt_C Calf Posts: 23 Re: Linkstation Pro (LS-WXL) Errors (red and orange lights) « Reply #2 on: November 07, 2011, 02:09:27 pm » Thanks for the reply†But when I look in http://contactmailsupport.com/buffalo-linkstation/buffalo-ls-qvl-error-codes.php a_id/12767 _________________Buffalo LS-QVL/R5 (FW 1.69 mod 1)Buffalo LS421DE (FW 1.31)Buffalo LS421DE (FW 1.31)Buffalo TeraStation TS5400D Top Profile Reply with quote gopher1369 Post subject: Re: flashing red light 6 times

I17 The RAID array is being resynchronized. *Data transfers will be slower than usual until this is complete . I26 Initializing the settings in the Web Admin interface. blinks green System booting or flash memory write in progress. When removing a USB device To remove a USB device connected to the LinkStation, hold down the Function button for at least three seconds.

Retrieved from "http://buffalo.nas-central.org/w/index.php?title=Information/LSProLED&oldid=25961" Categories: All PagesHowtoLSProFAQ Navigation menu Views Page Discussion View source History Personal tools Log in Buffalo Portal Home Page Linkstation Kurobox Terastation Recent Changes Main Portal Home Page I22 Erasing the data of the hard drive. Run the RAID array disk check in the LinkStation's Web Admin interface. Blinks Blue DirectCopy is in use.

Place Status Display example 10s place The LED illuminates for 1.0 seconds every 0.3 seconds. At that point another orage LED error on the NAS came on, this time 1 long + 1 short, which means "Many Bad Sectors found"†Now, and I know it's my own E22 Mounting of the hard drive failed. Try checking what the error represents from the info I posted on this page.

Information LED The Info/Error LED blinks orange when there is a message. Format the hard drive.