Home > Buffalo Linkstation > Buffalo Linkstation Duo Info Error Orange

Buffalo Linkstation Duo Info Error Orange

Contents

Link/Act LED Status Descriptions Glowing green Linking. I22 Erasing the data of the hard drive. I26 Initializing the settings in the Web Admin interface. Generated Mon, 15 Aug 2016 02:11:20 GMT by s_rh7 (squid/3.5.20) check over here

Please tell us how we can make this answer more useful. E16 Hard drive cannot be found. Note: The function LED (blue) and the info/error LED (orange) blink together if an error occurs during DirectCopy. Reformat the hard drive. 4 Fan problem. 5 ROM problem. 6 Hard Drive can not be recognized. 7 Problem with motherboard (RAM, LAN, or Hard Drive controller).

Buffalo Nas Drive Orange Light

Please try the request again. I21 Checking the hard drive. Privacy Policy | Sitemap Stay Informed…. Das USB-Ger√§t ist angeschlossen (leuchtet 5 Sekunden lang).

Or is it a hardware issue.†If Disk 2 is dying after only 2 years, whats the likely hood of disk 1 also going the same way?†Lastly, the cause - other than This error occurs when there is a firmware update available for your device and your version of NASNavigator2 is out of date. ← Previous Post Next Post → If you enjoyed Update the firmware. Buffalo Linkstation Flashing Red Light 3 Times After replacement, rebuild the RAID array by following the setup screen after starting the LinkStation.

I14 The RAID array is being checked. Rebuild the RAID array or format the hard drive in the Web Admin interface. After formatting and rebooting, if the error still apears, replace the drive. Concact technical support for assistance.

Format the hard drive. Buffalo Nas Amber Light It will run in degraded mode until the error is corrected. Replace the hard drive indicated by the red LED. I28 Eine USB-Festplatte wird formatiert.

Buffalo Linkstation Flashing Red Light

The number of flashes is the ones place of the error code. Leuchtet während der Initialisierung. Buffalo Nas Drive Orange Light Die Info/Error Led leuchtet orange. Buffalo Linkstation Red Light Flashing 7 Times Contact Buffalo technical support for assistance.

occurs during DirectCopy. check my blog Info/Fehler-LED Die Info/Fehler-LED blinkt rot, um einen Fehler anzuzeigen. Matt_C Calf Posts: 23 Re: Linkstation Pro (LS-WXL) Errors (red and orange lights) « Reply #6 on: November 07, 2011, 04:38:12 pm » If I can borrow another computer I will, And then it's up and running to accept copying data back to it from the USB drive? Buffalo Linkstation Solid Orange Light

Power LED Display Status Solid Blue The LinkStation is powered ON. Off Power is not connected. Great reviews Please contact me George | October 31, 2014 at 2:22 am Hello i have a flashing amber light is this bad? this content Try checking what the error represents from the info I posted on this page.

Stelle Status 10er-Stelle Alle 0,3 Sekunden leuchtet die LED 1 Sekunde lang auf. Buffalo Linkstation Degraded Mode I32 Appears when RAID rebuilding or formatting on the web Admin interface is necessary after replacing the hard drive. E12 System temperature has exceeded the maximum safe value.

Do not turn off the LinkStation power.

  • Matt_C Calf Posts: 23 Re: Linkstation Pro (LS-WXL) Errors (red and orange lights) « Reply #2 on: November 07, 2011, 02:09:27 pm » Thanks for the reply†But when I look in
  • Ratings: (0) | Views: 16,962 | Likes: 5. … The function LED (blue) and the info/error LED (orange) blink together if an error … Buffalo LS WSXL.
  • E14 Das RAID-Array konnte nicht angeschlossen werden.
  • Check that there are no objects around the LinkStation, or install at a cooler location.
  • Sign up!
  • After you have done this, you can just go to the Buffalo interface to remove the problem drive 1 and then put in a new drive.
  • E23 An error occurred, so the hard drive was removed from the RAID array.
  • So, and forgive my ignorance, is disk 2 dead/dying?

Alvi. Hope this helps Categories Android Phones Audiophile Buffalo Quad Pro NAS Computer Computer, Hardware, Software, How-to's Fujitsu ScanSnap S1500 Going Paperless Hardware How-to's HP Microserver N40L Miscellaneous Photography and Camera Gears E12 The system temperature has exceeded the safety value. Buffalo Linkstation Solid Amber Light Paket Home Starter 10 GB Speicherplatz4.99 ‚ā¨ / Monat mehr erfahren...

The number of flashes is the tens place of the error code.  E22 1s place The LED illuminates for 0.5 seconds every 0.3 seconds. Retrieved from "http://buffalo.nas-central.org/w/index.php?title=Information/LSProLED&oldid=25961" Categories: All PagesHowtoLSProFAQ Navigation menu Views Page Discussion View source History Personal tools Log in Buffalo Portal Home Page Linkstation Kurobox Terastation Recent Changes Main Portal Home Page Place of information code Status Display example 10s place of information code The LED illuminates for 1.0 seconds every 0.3 seconds. have a peek at these guys Werbung Suchtags buffalo linkstation duo led codes | buffalo ls-wxl info/error | buffalo nas error codes | http://www.nas-hilfe.de/buffalo-linkstation-mini/fehlerbehebung/202-die-status-led-der-linkstation-mini-ls-wsgl-oder-linkstation-mini-ls-wsxl-blinkt-blau-rot-gelb-oder-gruen-eine-uebersicht-ueber-die-status-codes | buffalo ls-wxl blinkt rot | buffalo linkstation info error | buffalo linkstation

I've had 3 drives fail on me in 7 years. The LinkStation will be shut down normally. I32 The RAID should be rebuit or a drive should be formatted.Normally this is displayed after a hard drive has been replaced. Fehlercodes Fehlerbeschreibung E00 MPU ist ungewöhnlich, kein Strom.

Blinks Blue DirectCopy is in use. I15 The error status of the RAID array is being investigated. *Data transfers will be slower than usual until this is complete. Yes No Thank you for your cooperation in the questionnaire. Logged Matt_C Calf Posts: 23 Re: Linkstation Pro (LS-WXL) Errors (red and orange lights) « Reply #9 on: November 08, 2011, 01:54:14 pm » Thanks.

Detach the USB device from the LinkStation. 3. Info/Error LED The Info/Error LED blinks orange when there is a message.