Home > Brother Printer > Brother Fax Error Codes

Brother Fax Error Codes

Contents

The remote machine disconnected immediately before sending any further fax tones or T.30 frames. If the local machine consistently gives this error code from different fax numbers, then the issue is probably hardware related and the machine should be replaced or serviced. Remote diagnostics cannot occur between machines with incompatible remote versions. Error on “Poor Copy Quality”: This error message usually appears when your Brother fax machine is a 900 series made from 1993 until 1994. http://contactmailsupport.com/brother-printer/brother-error-codes-76.php

If the error persisits, the ink loader unit may need attention. The call-waiting service can cause this error. Try sending at a lower transmission speed. Slide this from side to side making sure to return it to its' home position and reinsert it into the machine.

Brother Printer Error Codes And Solution

Explanation: Check the printhead to see if anything is stuck to it. Z7_3054ICK0KGTE30AQO5O3KA30H5 hp-country-locator-portlet Actions ${title} Loading... What to do: Error Code: 52 Error Code: Replace Tray 1 Feed Kit: The feed rollers and retard pad for the main paper tray have reached the end of their specified If error persists, then the waste toner sensor may be faulty.

  1. You will need an engineer to replace the laser unit.
  2. If it still fails, try receiving a fax from another machine.
  3. The click, heard for an incoming call, is actually a momentary disconnect of the line.
  4. You just have to reboot your desktop and it will be fine afterwards. “Machine Error” Issue: This error is common to Brother Fax machines wherein the device will make that long
  5. HP Fax Products - Fax Error Codes and Solutions This document is for HP fax products.

If error persists then the fuser will need replacing. Explanation: Switch the fax machine off and back on again. Ask the user of the remote machine to turn it off for 10 seconds, and then turn it back on. Brother Printer Error Light What to do: Machine Error: B9 Error Code: Scanner Error: The scanner unit reads the information on the outgoing document and a problem with its light intensity has been detected.

Make sure the remote machine can accept and use polling. Brother Printer Error Message If the error persists, then the fuser unit will need replacing. Explanation: Remove paper tray and look for jammed paper. Confirm that the remote fax machine is ready to receive a document, and then try sending the fax again. 313 A busy signal was detected each time the local machine attempted

Retry the fax reception when telephone line conditions have improved. Brother Printer Troubleshooting Guide If nothing is found, then there may be a problem with the paper sensors. What to do: Error: 76 Error Code: Fuser error: The fuser unit is the part of the machine that gets hot and bonds the print onto the page and the printer Explanation: Worn fuser units can cause poor quality print and paper jams.

Brother Printer Error Message

Explanation: Switch the machine off and back on again. The click, heard for an incoming call, is actually a momentary disconnect of the line. Brother Printer Error Codes And Solution Remove any pass-through devices from the phone line, and then try the fax again. Brother Mfc Error Codes Explanation: The drum unit needs replacing and the drum life counter resetting.

Explanation: Switch the printer off and back on again. have a peek at these guys Explanation: Check for debris in the document feeder area. Explanation: Switch the machine off and back on again. If error persists, then the document feed rollers may need replacing What to do: Machine Error: A7 Error Code: Document Feed Error: The machine has detected a problem when transmitting a Brother Printer Error 50

Also look for debris in paper feed path. Both machines have attempted to start a reception at the same time. Enable or disable the ECM setting. http://contactmailsupport.com/brother-printer/brother-mfc-error-codes.php The alphanumeric code is used by looking up the relevant description in the user manual.

If the document is large, ask the remote user to re-send the document as two or more smaller documents. Brother Printer Error 4f Try the fax when telephone line conditions have improved. If the error persists then the fuser will need replacing.

We are now investigating the problem.

Explanation: Check the paper path is clear of obstructions. Resend at a lower resolution. What to do: Machine Error: A2 Error Code: Document Feed Error: The machine has detected a problem when transmitting a document. Brother Sewing Machine Error Codes We are now investigating the problem.

If error persists then the laser safety flap may be defective or the laser unit may need replacing. Ask the remote machine user to reset the remote machine. The paper is not correctly loaded and the document sensor cannot sense it. this content Explanation: Switch the machine off / on.

Disable ECM. If error persists then an engineer will be required to check the sensors. These errors can occur if the phone lines in the area to be faxed are old or there is noise (static on the phone line). FAQS Call us to get a free quote 0800 0186 222 Home just printers multi-functional printers fax machines common errors the team about us contact You are here:Home/Common Errors Troubleshooting common

Retry the fax reception when line conditions might have improved. This relates to the scanner motor. If fault does not clear, the laser unit will need replacing What to do: Machine Error: 72 Error Code: Beam detect error: The laser unit produces a beam to write the Support Forum Join the conversation!

Enable the remote diagnostics capability on the local machine, if available. This occurs when the line is disconnected or if line conditions degrade during the session. What to do: Error Code: 50 Error Code: Replace Drum Unit: The drum unit has printed the specified number of pages for its life cycle. Have the telephone company check the line. 431 The sending fax machine did not receive a response after terminating a transmission.

Explanation: Check the paper path and gently remove any trapped paper. What to do: Error Code: 50 Error Code: Replace Drum Unit: The drum unit has printed the amount of pages specified for its life cycle. It can also be caused if the receiving fax is using a fax format incompatible with the HP fax (usually during color faxing). If nothing is found, an engineer will be needed to determine the cause.

Check path for obstuctions and remove any foreign materials. Explanation: Switch the printer off and back on again. What to do: Machine Error: 8B Error Code: Printhead Error: The machine has detected that the thermal printhead is overheating. These error messages are there to help you troubleshoot your Brother machines fault and can help us assist you in resolving the problem.

Depending on your printer, a fax error code might display on the printer control panel or on a fax history report. If nothing is found you will need an engineer to check the paper sensors. Disable ECM. This is collected in a waste ink tank and this has become full.