Home > Brother Printer > Brother Error E52

Brother Error E52

Contents

Too hot, not hot enough, not heating up at all. Brother MFC 240C... Again, not too much – wipe the excess.7 – Put everything back together.That worked very well for me and my HL-1670n is back to his nice purring noise. Again, not too much wipe the excess.7 Put everything back together.That worked very well for me and my HL-1670n is back to his nice purring noise.Good luck. weblink

Replace the Engine PCB. If you do, you can always clean with isopropyl alcohol or glasses solution. [Since you have to touch the mirror to lift it, I just cleaned it routinely with an alcohol Brother MFC 240C... If fault persists, the fuser unit will need replacing.

Brother Printer Problems And Solutions

PDF Manual UserManual_English.pdf.... Question about HL 1670N Laser Printer 1 Answer Brother HL-1670n failing to feed paper. ...shaft. Thanks to the folks that posted the fix many years ago.

LiamH and all other wizards, thanx very much.Greetings from Amsterdam, Holland. I used machine oil SAE 20 or 40 (not sure I didnt look). by Anonymous on Dec 22, 2007 at 7:42pm Add comment Please sign in to comment 0 I called a service shop who looked up the code "EF5" code and told me Brother Fax Machine Error Codes What to do: Error: E51 Error Code: Malfunction of laser unit: The laser unit is the part of the printer that writes the information on the drum surface.

What to do: Error Code: 5E Error Code: Replace the Belt Unit: The transfer belt has reached the end of its specified life cycle. Brother Printer Error Message If the problem persists then the laser will need replacing. I just can't believe that this unit would be suffering from "wear" as it's only on it's 2nd toner cartridge ever! Explanation: Remove paper tray and look for paper in path.

MAKE NOTE OF HOW AND WHERE IT GOES ONCE YOU EXTRACT IT]4 – Squeeze out the laser unit from under the wires (going back and up).[This would not have worked for Brother Mfc Error Codes If it is not then the paper sensor may be faulty. step 1 step 1 choose your brother printer Choose a printer family Printer Family Just-Printers Multi-functional-Printers Fax-machines Printer Family step 2 choose your brother model step 2 Choose your Brother Model If the error persists, then the fuser unit will need replacing.

  • ERROR E50 Malfunction of fuser detected ERROR E51 Malfunction of laser beam detector ERROR E52 Malfunction of laser unit motor ERROR E54 Malfunction of main motor ERROR E55 Malfunction of high-
  • What to do: Error Code: 31 Error Code: Density sensor failure: The print density is checked by a sensor looking at samples of toner placed on the belt.
  • Open the body of the printer and check for jammed paper.
  • There is a plastic shutter that will come loose.
  • IF YOU TRY TO PUT THE LASER ASSEMBLY AND PLATE PIECES TOGETHER WITH THE METAL PLATE ON THE DOWN SIDE, THE SHUTTER WILL FALL OUT OF ITS POSITION AND CAN CAUSE
  • It is saying that the document is too long to be scanned.
  • Just remove it and unplug the connector.•Now squeeze out the laser unit from under the wires.Now you have the laser unit outside of the printer machine.•Just remove the steel plate of
  • Explanation: Replace drum unit.
  • Thank you, I now have a working Brother HL-1650 for the low, low price of 30 minutes or so of my time and a single drop of oil.

Brother Printer Error Message

by unknown on Feb 17, 2011 at 8:45am Add comment Please sign in to comment 0 Works great and perfectly!So my 8 years old HL-1650 will work still al long time.Thanks If so, can I fix it? Brother Printer Problems And Solutions If error persists, then the paper pick-up rollers may need replacing or the paper path need cleaning. Brother Printer Error Printing What to do: Error: 76 Error Code: Fuser error: The fuser unit is the part of the machine that gets hot and bonds the print onto the page and the printer

An error has been detected while trying to send / receive a fax. http://contactmailsupport.com/brother-printer/brother-error-e51.php Twist it and remove it. [Twist it 90 degrees is sufficient; no need to remove it.]4 – Pull up the mirror part. 5 – Be careful during all that not to by Anonymous on Sep 13, 2006 at 2:42pm Add comment Please sign in to comment 0 I replaced the fuser drive gear, and turned the printer on, and got and error Explanation: Switch the printer off and back on again. Brother Printer Error Light

This is collected in a container which is now full. Thanks to all that posted on this thread. If nothing is found, the duplex unit may need servicing. check over here Same result :Error E52".

Explanation: Check the printhead to see if anything is stuck to it. Brother Printer Troubleshooting Print Quality Your right about the fix though that should do it but I think you copied some elses post I might be wrong and no do not use wd40. What to do: Machine Error: 8809 Error Code: Recording Paper Jam: The paper sensor has detected paper in the path before stating the paper feed.

BTW I used 1 drop of Singer "All Purpose Machine Oil" - purchased at my local sewing supply store (JoAnne's Fabrics on Riverside in Sherman Oaks, CA)I used a microfiber glasses

Lithium grease is a good idea. Some people on this site fix noisey or failed scanners by lubricating the scanner motor bushings. IT'S JUST A METAL PLATE THAT HELPS LOCK THE CONNECTOR IN ONCE ASSEMBLED. Brother Printer Error State You might want to disconnect the shorter one. [Do disconnect the shorter one.]3 – Remove the laser unit located on top of the printer covered by a steel plate.To do that:1

Using an optical cloth to lift the mirror unit will reduce affection of the mirror unit to a minimum. Explanation: Switch the fax machine off and back on again. Im in Sudbury Resolved Question: E52 error display service call. this content Leave the board in place.] ON MY PRINTER THERE ARE THE 4 SCREWS MENTIONED PLUS A FIFTH SCREW THAT TIGHTENS AGAINST A FLANGE OF THE MOTOR COVER AND HOLDS THE MOTOR

If the error persists, then the document feed rollers may need replacing. Explanation: Switch machine off and back on again. the swing arm should be positioned on the outside lower left of the laser unit, while the rest of the piece is inside, held in place by two circular-shaped molds -- Explanation: Check the paper path and gently remove any trapped paper.

has been printing again all night no probs :) by unknown on Dec 4, 2006 at 7:23am Add comment Please sign in to comment 0 How do I fix or clean Followed the instructions for E52 and it worked like a charm. by unknown on Dec 16, 2012 at 9:43am Add comment Please sign in to comment 0 Thanks so much for posting those detailed instructions for fixing the E52 Error. by Anonymous on May 26, 2010 at 8:02pm Add comment Please sign in to comment 0 Yet another printer fixed.

If the error persisits, the ink loader unit may need attention. Leave the board in place.]3 – There is a small piece of black plastic that maintains the top part of the motor unit (with the mirrors) on the left side of Check for paper in the body of the printer.