Home > Beep Codes > Bios Error Codes

Bios Error Codes

Contents

Once an operating system is running on the computer the code displayed by such a board may become meaningless, since some OSes, e.g. Startup tone, drive spins, no video Problem with video controller. Try yanking out the cards one by one to isolate the culprit. The pattern of beeps whether its the number of beeps or the length of those beeps will give you an indication of the actual problem. Source

instead If you receive this message after making changes in the setup program, enter the program and restore the original values(s) Press to resume, to Setup This message is Each 1 in the map indicates a failed bit If you receive this message after making changes in the system setup program, enter the program and restore the original value(s) Fixed If this doesn't do it, the memory chips may be bad. As the PC platform evolved into more of a commodity consumer device, the mainframe- and minicomputer-inspired high-reliability features such as parity memory and the thorough memory test in every POST were http://www.pcmag.com/encyclopedia/term/38515/beep-codes

Gigabyte Beep Codes

Later BIOSes used a sequence of beeps from the motherboard-attached loudspeaker (if present and working) to signal error codes. Then the computer continues to boot. In earlier BIOSes, up to around the turn of the millennium, the POST would perform a thorough test of all devices, including a complete memory test. If not, you have a parity error in your first 64K of memory.

  1. Then the computer continues to boot.
  2. How to Troubleshoot and Solve USB Device Error Code 10 Spooler Subsystem App has encountered a problem and needs to close Error and How to Fix it How to Fix Problem
  3. My Web Search Removal Help Ten Steps to Trouble-Free Computing Know Your System Create an Emergency Boot Disk Tune Your Hard Drive Store With a Plan Backup Your Data Keep Your
  4. Codes for different BIOS versions from a single supplier may also vary, although many codes remain unchanged in different versions.
  5. The browser version you are using is not recommended for this site.Please consider upgrading to the latest version of your browser by clicking one of the following links.
  6. Video error (no add-in graphics card installed) Reseat add-in graphics card.
  7. You need a new motherboard. 1-2-2 The motherboard is bad. 1-2-3 The motherboard is bad. 1-3-1 You'll need to replace the motherboard. 1-3-3 You'll need to replace the motherboard. 1-3-4 The

Replace the IC if possible 2-2-1 64KB RAM failure Bit 4; This data bit on the first RAM IC has failed. Try running the setup program that comes with the computer. I verified this with a SIIG (crap -- avoid like the plague) Ultra-66 card, and then confirmed the results with Dell. Intel Beep Codes Reseat the video card.

Most clone PC BIOSes allowed the user to skip the POST RAM check by pressing a key, and more modern machines often performed no RAM test at all unless it was Replace the controller if possible 3-1-2 Master DMA register failure The DMA controller had failed. Is everything connected? http://www.pchell.com/hardware/beepcodes.shtml The exponential growth of PC memory sizes, driven by the equally exponential drop in memory prices, thanks to Moore's Law, was also a factor in this, as the duration of a

Check that the thermal interface material is sufficient and is spread evenly. Beep Codes List If so, try swapping it with another one and see if it works. 3-4-_ Your video card isn't working. In the event of a fatal error, the Mac will not make its startup chime. Sign in here.

Asus Beep Codes

If the I/O is on the motherboard itself, disable them with a jumper (consult your manual to know which one) and then add an I/O card. 4-4-2 See 4-4-1, but this http://www.pcmag.com/encyclopedia/term/38515/beep-codes Use at your own risk. Gigabyte Beep Codes This article mainly deals with personal computers, but many other embedded systems such as those in major appliances, avionics, communications, or medical equipment also have self-test routines which are automatically invoked Beep Codes Dell You could probably get away with just replacing the CPU, but that's not too cost-effective.

Beep Code Description 1 long, 2 short Indicates a video error has occurred and the BIOS cannot initialize the video screen to display any additional information 1 long, 3 short Video http://contactmailsupport.com/beep-codes/bios-error-codes-phoenix.php If a key appears to be stuck, carefully pry it up. Reseat RAM chips or replace RAM chips as possible solution 1-1-1-3 Verify Real Mode. 1-1-2-1 Get CPU Type. 1-1-2-3 Initialize system hardware. 1-1-3-1 Initialize chipset registers with initial POST values. 1-1-3-2 PCMag Digital Group PC, PC Magazine and PC PCMag.com are among the federally registered trademarks of Ziff Davis, LLC and may not be used by third parties without explicit permission. Hp Bios Beep Codes

Replace the motherboard 3-2-3 Reserved 3-2-4 Keyboard controller failure The keyboard controller has failed. Award Software cannot supply upgrades for a BIOS that has been subsequently modified by hardware vendors." To make matters worse, Award BIOS merged with Phoenix Technologies in 1998. Check that the thermal interface material is sufficient and is spread evenly. have a peek here Reseat them and reboot.

Replace the IC if possible 4-3-4 Time of day clock failure The real time clock/CMOS has failed. Msi Beep Codes If it does the same thing, one of the memory chips on the motherboard are bad, and you most likely need to get another motherboard since these chips are soldered on. These other duty-specific programs are generally known collectively as option ROMs or individually as the video BIOS, SCSI BIOS, etc.

Award's website states "Award Software software products are sold to a board or system manufacturer ("hardware vendor"), who customizes them further before selling the system.

All chips associated with the CMOS will likely have to be replaced. Replace the IC if possible 3-1-1 Slave DMA register failure The DMA controller has failed. Phoenix BIOS beep codes Below are the beep codes for Phoenix BIOS Q3.07 OR 4.X Beep Code Description and what to check 1-1-1-1 Unconfirmed beep code. Computer Beep Codes Pdf Best bet is to install another video card. 9 Short Beeps Your BIOS is bad.

IBM BIOS beep codes Below are general IBM BIOS Beep codes that can occur. Replace the CMOS if possible 1-1-4 BIOS ROM checksum error The BIOS ROM has failed. However, because of the wide variety of different computer manufacturers with this BIOS, the beep codes may vary. Check This Out Find us on Google+ System Specific Diagnostic and POST Error Messages: IBM Diagnostic Error Codes Compaq Desktop Systems Diagnostic and POST Errors BIOS Related Pages: BIOS Data Area BiosCentral Forums BIOS

With this audio code in hand, you can determine what part of the system is having problems and find a solution. Submitted by John Palmer. Reseat or Replace the BIOS. 10 Short Beeps Your problem lies deep inside the CMOS.